P2B-DS Pentium III 1000 nicht erkannt HILFE !!

pentiumIII

Cadet
Mitglied seit
06.06.2015
Beiträge
50
Renomée
0
Standort
Graz, Österreich
Hallo erstmal ...

Ich hab heute mein P2B-DS mit nem PIII 500 bekommen
.... So weit so gut, mit dem 500er startet es normal

Problem: meine zwei 1000er werden nicht erkannt ... auch nicht nach dem Update auf das Bios 1014.003 Beta ... :(:(
was könnte da sein ???

Bitte helft mir

--- Update ---

(P2B- REV 1.04 )

--- Update ---

... und mit den beiden Katmais die ich habe (450 und 500 ) funzt es ...
die beiden 1000er sind coppermines

--- Update ---

Könnte es sein dass ich mal zurück auf Bios 1013 Flashen muss?, weil da steht was von Coppermine in der beschreibung ...
 
Neee ... 60€ für nix ??

--- Update ---

Gibts da wirklich nichts was man da machen kann ??
???

--- Update ---

da gibds ja irgendwas mit Pin Mods ... A: Yes it's possible, but it requires some work. The basic idea behind the modification is the same as if you would be using a slotket adapter and use the voltage selection jumpers to make the board believe the cpu wants a different voltage.
There are 5 voltage identification signals (called VID0 - VID4), which must be altered (you don't need to touch VID4). To do this, you must tape some pins on the slot1 connector, and connect some others. It depends on the default voltage of your cpu which pins you'll have to modify, there are 3 possibilities. In all cases, you need to change the VID coding to 1.8V, i.e. (VID0 to VID3, from left to right) 1 0 1 0. A "0" means the signal is connected to ground, a "1" means it is open.
1.7V cpus: The cpu VID coding is (VID0 - VID3): 1 1 1 0. Only VID1 is different from the target 1.8V VID encoding, so you have to alter only VID1 to a logical 0. To do this, you need to connect VID1 to ground. VID1 is pin A120 on the connector, connect this to the adjacent A121 pin using a thin u-shaped wire piece.
1.65V cpus: cpu VID coding is (VID0 - VID3) : 0 0 0 1, so both VID0 (pin B120) and VID2 (pin A119) must be changed from a logical 0 to a logical 1. This can be done by insulating them, so just tape them. Additionally, VID3 (pin B119) must be changed to 0, thus needs to be connected to ground. Unfortunately, there is no adjacent ground pin, so use an insulated wire to connect it to A121 (just "around the corner" of the edge connector).
1.6V cpus: cpu VID coding is (VID0 - VID3): 1 0 0 1. Connect VID3 (pin B119) to A121 using an insulated wire. Tape VID2 (pin A119).
More information on this mod (including the mandatory pictures) can be found at http://tipperlinne.com/p2b-ds. If you're curious, you can get information about all VID codings from the PII/PIII datasheets at developer.intel.com.
If you don't want to use wire tricks, there is also another method - replace the voltage regulator with one which can go below 1.8V (e.g. HIP6019CB and HIP6019BCB are pin-compatible). However, you'd need to get the newer regulator chip (probably from a defective board) and then exchange the chips, which you probably should only do if you're experienced with smd-soldering.
But don't come back and complain your board went up in smoke! It should be obvious you do all modifications on your own responsibility.

--- Update ---

was man aus Verzweiflung nicht alles machen will ... http://tipperlinne.com/p2b-ds.htm

--- Update ---

Kurz gesagt ... wenn ich die letzten zwei Pins (A120 und A121) am Slot überbrücke, müsste das Ding auf 1,8 V laufen und den 1000er annehmen ...
Ich hab Angst was kaputt zu machen, deshalb warte ich noch ...

--- Update ---

OK .. Die U s hab ich jetzt zurecht gebogen ....

--- Update ---

was meint ihr ... soll ich es wagen ??
 
AAAAAAAAAAAHHHHHH !!!!!!!!!!!!

ES HAT FUNKTIONIERT ... Pentium III 1000, 2 Processors Detectet
... @ 1.8 V

*massa**clap*;D:D*rofl*

--- Update ---

Asus P2B-DS Rev 1.4 Coppermine Upgrade .. was du brauchst : 2x 0.25x6 mm Draht und eine Pinzette ... :)
 
Na also! Meins ist nämlich auch kein 1.06er. Jetzt weiß ich schonmal daß das klappt ;).
 
DAS GIBTS DOCH NICHT !! :[

Wer meinen alten Beitrag übers P6DGU gelesen hat, hat vermutlich meine Verzweiflung bei der Installation als Multi oder uniprozessor mitverfolgt ...

wer hätts gedacht, Ich hab schon wieder das gleiche Problem ...

--- Update ---

Achja ... ausserdem zeig es mir immer nur den halben Ram im Bios an ... bei 1GB steht da 524mb und bei 256 MB steht 128 mb
 
Habs nicht gelesen...was gabs da für ein Problem?

Ich hatte mal ähnliche Probleme mit einer anderen Plattform. Da fehlte der ACPI Multiprozessorsupport und es wurde nur ein "Standard PC" installiert. Konnte aber durch deinstalieren des selben und manuell installieren des ACPI Multiprozessorblablubbs einfach aktiviert werden. Evtl. ist es bei dir nur ne BIOS Option....


Welche Speichermodule hast du verbaut? Organisation Module?
Der BX kann maximal 16Mx8 verwalten. Wenn du jetzt Module mit 32Mx4 verwendest, wird halt nur die Hälfte erkannt, weil die Speicherdichte zu hoch ist, bzw. dem Chipsatz erforderliche Adressleitungen fehlen um das anzusprechen.

S. auch hier:
http://www.heise.de/ct/hotline/Tueckische-128-MBit-SDRAMs-310570.html
 
Zuletzt bearbeitet:
Also : wenn ich bei der installation mit F5 ACPI Oder MPS Multiprozessor auswähle dann hängt das Setup bei Setup startet Windows 2000 ...
 
Ich muss da erstmal wieder reinkommen....diese Hardware hatte ich schon seit 15 Jahren nicht mehr unter den Händen^^

Wie lange hängt es? Manchmal hat Windows die Unart, diese scheinbare Inaktivität auch mehrere Minuten durchzuhalten, nur um dann unvermittelt weiter zu machen.
Ansonsten prüfe doch mal die Bios Optionen, ob das was klemmen könnte. ACPI aktiviert?


EDIT:

Ich les grad...Board-Revisionen bis 1.05 machen Probleme mit ACPI unter W2K und müssen Hardwaremäßig modifiziert werden.
Nähere dazu hab ich auf die Schnelle nicht gefunden.

EDIT:

To fix the ACPI problem, all you have to do is moving an SMD resistor
near the APIC. (Of course that's a gross understatement if you're not
routined in SMD soldering.) The FAQ page covering this issue is here:
http://rma.asus.de/support/faq/faq075_W2K_ACPI_dual-mb.htm
I don't think there ever was anything official for the USB issues. But
searching did turn up this:
http://www.hole.fi/~dogo/p2b-usb/
Apparently you need to replace R112 by a zero ohm resistor.
I think the older board revisions were also affected by the bus
termination voltage issue discussed here:
http://www.angelfire.com/electronic2/locksmith/asusreworkguide.html
http://www.pcreview.co.uk/threads/xp-setup-hangs-with-dual-piii-550-on-asus-p2b-ds-v1-04.2187207/
 
Zuletzt bearbeitet:
OK.. Das Setup hängt ewig .... man kann auch nicht mehr mit Strg+alt+entf neustarten ...
das ACPI Problem: der Vorbesitzer hat den Wiederstand R80 auf R79 schon umgelötet :)
Im BIOS Gibts nix mit ACPI zum auswählen ...
Den XP Thread les ich selbst grade ...;D
Ich versuchs grad mit MPS, und wenn das nicht funzt dann versuch ichs mit NT4

--- Update ---

MPS ... nix

AUF zu NT4

--- Update ---

OK.. Bei der NT4 Installation .... Es Schreibt : 1 Systemprozessor ; Multiprozessor Kernel .... Sind da meine Prozessoren im A**** ???

Weil alleine funktionieren beide ...

--- Update ---

-HILFE- Schon das 2. mal dass mir das passiert :(
 
Ist der umgelötete Widerstand noch ok? Kalte Löststelle evtl.? Leiterbahn/Lötpads noch intakt?
 
OK .. Ich hab so das gefühl das es irgendwas softwaremäßiges sein muss ... es können nicht 2 Boards defekt sein oder ??

--- Update ---

OK .. Habs jetzt hinbekommen das ich von CD Booten kann ...

Installier grad XP auf ACPI MP ... bin grad beim Formatieren ... mal schauen was wird .. im moment siehts gut aus .. :)

--- Update ---

OK ... Windows XP installiert und siehe da : Im gerätemanager lese ich "ACPI Multiprozessor PC" und im Taskman gibts 2 Fenster ...

Jetzt muss ichs nur noch mit Win 2k hinbiegen ...

--- Update ---

;D;D

--- Update ---

Mann ... unterschätzt nie die Macht eines ZIP Laufwerks ...... :P
 
Zurück
Oben Unten